4TECH 9G21730 FRR5H is a Standard Flow 30% Mineral / Glass Filled FR-V0 Halogen & Red Phosphorous Free, Heat Stabilised PPA
| General Property | Test Procedure | Units | Value Dry - (Cond.) |
|---|---|---|---|
| Moisture Content | ***** | ***** | ***** |
| Shrinkage | ***** | ***** | ***** |
| Shrinkage | ***** | ***** | ***** |
| Specific Gravity | ***** | ***** | ***** |
| Water Absorption (24Hrs - 50% RH, 23°C) | ***** | ***** | ***** |
| Thermal Property | Test Procedure | Units | Value Dry - (Cond.) |
|---|---|---|---|
| Ball Pressure | ***** | ***** | ***** |
| Deflection Temperature @ 1.8 Mpa | ***** | ***** | ***** |
| Melt Temperature - 10 K/min | ***** | ***** | ***** |
| Vicat Softening Temperature - 50N | ***** | ***** | ***** |
| Mechanical Property | Test Procedure | Units | Value Dry - (Cond.) |
|---|---|---|---|
| Charpy Impact Strength - Notched, +23°C | ***** | ***** | ***** |
| Charpy Impact Strength - Un-notched, +23°C | ***** | ***** | ***** |
| Izod Impact, Notched, -30°C | ***** | ***** | ***** |
| Izod Impact, Notched, +23°C | ***** | ***** | ***** |
| Tensile Modulus 5mm/min, +23°C | ***** | ***** | ***** |
| Tensile Strain @ Break, 5mm/min, +23°C | ***** | ***** | ***** |
| Tensile Stress @ Break 5mm/min, +23°C | ***** | ***** | ***** |
| Electrical Property | Test Procedure | Units | Value Dry - (Cond.) |
|---|---|---|---|
| Comparative Tracking Index | ***** | ***** | ***** |
| Flammability Rating 0.75mm | ***** | ***** | ***** |
| Flammability Rating 1.6mm | ***** | ***** | ***** |
| Glow Wire Flammability Index (GWFI) - 2 mm Plaque | ***** | ***** | ***** |
| Glow Wire Ignitability Temp (GWIT) - 2mm Plaque | ***** | ***** | ***** |
| RTI ELECTRICAL STRENGTH @ 20,000 Hours (Internal) | ***** | ***** | ***** |
| RTI IMP @ 20,000 Hours (Internal) | ***** | ***** | ***** |
| RTI IMPACT @ 20,000 Hours (Internal) | ***** | ***** | ***** |
| RTI STR @ 20,000 hours (Internal) | ***** | ***** | ***** |
| Surface Resistivity | ***** | ***** | ***** |
| Volume Resistivity | ***** | ***** | ***** |
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to verify the information currently provided - especially that contained in our safety data and technical information sheets - and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.
Test Values: Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Kindly note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mould/ die, the processing conditions and the colouring.
4PLAS LTD, 812 Fountain Court Birchwood Boulevard, Birchwood, WARRINGTON, WA3 7QZ, UK
+44 870 446 0424